- Sort by Popularity
- Display 12 Products per page
-
611655-021 | Individual Metric Rectangular Gauge Blocks – 15.5mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 15.5mm | Mitutoyo
Order No. : 611655-021
Length : 15.5 mm
Description :
This Grade 0 Gauge Block with Inspection Certificate offers you the following benefits:
- Outstanding dimensional stability: Mitutoyo steel gauge blocks are made exclusively from artificially aged material.
- High gauge reliability: The gauge blocks can be used as a standard for a long time due to their high dimensional stability.
- The maximum permitted length changes to gauge blocks over a year are defined in EN ISO 3650. Mitutoyo high-quality gauge blocks easily meet these and all other requirements.
- Steel gauge blocks are excellent for use as a standard because of the low measurement uncertainty that can be achieved when using them.
- Mitutoyo steel gauge blocks have top-quality surfaces, guaranteeing high wringing force.
-
611677 | Individual Metric Rectangular Gauge Blocks – 70mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 70mm | Mitutoyo
Order No. : 611677
Length : 70 mm
Description :
• If using only one length repeatedly, it is suggested to purchase individual gauge blocks.
• Nominal sizes which are not included in the chart below can be supplied custom-made on request.
• Each Grade K gauge block to ISO/DIN/JIS, BS or ASME standard is supplied with a Certificate of Calibration which certifies that the gauge block was calibrated by interferometry. -
148-866 | Micrometer Heads – Small Thimble Dimeter Standard Type – SERIES 148 | MITUTOYO
MICROMETER HEAD – SMALL THIMBLE DIMETER STANDARD TYPE – SERIES 148
Order no. 148-866
Range: 0-13mm
Description :
• Measuring range of 13 mm.
• The thimble can be set to zero at any position by loosening the setscrew. -
ROUNDTRACER FLASH | MITUTOYO
ROUNDTRACER FLASH
Non-contact form measuring system based upon state-of-theart 2D image sensors.
The Perfect Combination of Precision and “Flash” Cycle Time
The 2D image architecture sets a new benchmark in the measuring industry, providing significant advantages.
High Speed
Unrivaled measuring speed, thanks to the no Z-axis movements. Full 2D optic.
Image Consistency
Complex profiles and part geometries are acquired inside the same image frame.
Axial Run-out
The 2D image frame allows for the entire surface to be captured dynamically, at each angle, during the part rotation.
Thru-holes Measurement
Only a few milliseconds are needed between the image acquisition and the measurement execution.
-
182-534-10 | WORKING STANDARD SCALES SERIES 182 | MITUTOYO
• High-precision glass scales manufactured under Mitutoyo’s leading-edge Linear Scale production technology. They are available in various types and sizes to suit to your application.
• Ideal for checking magnification accuracy of profile projectors and microscopes, and the table feeding accuracy of measuring equipment.
-
368-002 | Holtest – Two Point Internal Micrometer Holtest 2.5-3 mm | MITUTOYO
2-POINT INTERNAL MICROMETER HOLTEST | MITUTOYO
Order No. 368-002
Range. 2.5-3mm
Description
• Titanium-coated measuring pins on the three-point type (over 6 mm range models) provide excellent durability and impact resistance.
• Three-point internal micrometer with measuring range 6 mm or longer allows stable measurement through self-centering.
• Measurement can be made close to the bottom of a blind hole.
• Deep holes can be measured by attaching an Extension Rod (optional) which is available on models over 6 mm (0.275 in) measuring range. -
552-155-10 | ABSOLUTE COOLANT PROOF CARBON FIBER CALIPER SERIES – with Ceramic Jaws, 0-450mm | MITUTOYO
ABSOLUTE COOLANT PROOF CARBON FIBER CALIPER SERIES 552
with Ceramic Jaws
Order No. : 552-155-10
Range : 0-450mm
Description :
This is a lightweight standard model of Digimatic caliper with ceramic jaws.
It offers you the following benefits:- Its ultra-lightweight design (with carbon fiber reinforced material) reduces total weight by up to 50%.
- It has excellent resistance against water and dust (IP66 protection level) enabling you to use it in machining situations that include splashing coolant fluid.
- Direct readout of inside measurements from the LCD (you can easily set the offset value by using the offset button).
- Preset function lets you set a desired starting point.
-
422-230-30 | Blade Micrometer – Non-Rotating Spindle Type Series 422 | MITUTOYO
Blade Micrometer – Non-Rotating Spindle Type Series 422
ไมโครมิเตอร์ปากมีด
Order No. : 422-230-30
Range : 0-25 mm
• The anvil and spindle are blade-shaped for measuring the groove diameter of shafts, keyways, and other hard-to-reach features.
• Carbide-tipped measuring faces are available.
• Non-rotating spindle type.
• Equipped with Ratchet Stop for constant measuring force. -
02AZF300 | CONNECTION UNIT, U-WAVE FIT STANDARD TYPE | MITUTOYO
CONNECTION UNIT, U-WAVE FIT STANDARD TYPE
Description
• This connecting part connects a measuring tool to its U-WAVE T unit. Choose the appropriate cable for your measuring tool from the seven types below, A to G.
-
293-254-30 | Coolant Proof Micrometer with Dust/Water Protection Conforming to IP65 Level Series 293 | MITUTOYO
Coolant Proof Micrometer
with Dust/Water Protection Conforming to IP65 Level Series 293
Size : 200-225 mm
-
293-341-30 | Coolant Proof Micrometer with Dust/Water Protection Conforming to IP65 Level Series 293 | MITUTOYO
Coolant Proof Micrometer
with Dust/Water Protection Conforming to IP65 Level Series 293
Range :1-2″
• Superior environmental resistance.
• Ratchet thimble provides better operability for one-handed operation.
• Measuring faces: Carbide.
• Oil-resistant material used for all plastic parts.
• Models equipped with a Digimatic output port can form part of a statistical process control or networked measurement system.
