- Sort by Popularity
- Display 36 Products per page
-
511-805 | BORE GAGE SERIES 511 – WITH MICROMETER HEAD, 150-250mm | MITUTOYO
BORE GAGE SERIES 511 – WITH MICROMETER HEAD
Order No.: 511-805
Range: 150-250 mm
Description:
• This series includes models for measuring ø60 to 800 mm inside diameters.
• The micrometer head is used for dimensional setting. The dimension can be easily changed without replacing the anvil and washer.
• The contact point has a carbide ball tip that is highly durable and abrasion-resistant.
• The grip minimizes the variation of indicator values affected by heat transfer from the operator’s hand. -
953555 | EXTENSION ROD SERIES 511 – ACCESSORIES FOR BORE GAGE | MITUTOYO
EXTENSION ROD SERIES 511 – ACCESSORIES FOR BORE GAGE | MITUTOYO
Order No. 953555
Description
• Extension Rods enable measurement of deeper holes when attached to a bore gage.
Note 1: When using an extension rod that is 500 mm or longer, hold the bore gage upright during measurement.
Note 2: Only one extension rod can be attached to a bore gage. It is not possible to use more than one extension rod.
Note 3: The extension rod cannot be used for products with a custom size or custom specifications.
-
177-132 | SETTING RINGS SERIES 177 – STEEL | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-132
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
177-427 | SETTING RINGS SERIES 177 – CERA | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-427
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
468-173 | Digimatic Holtest – 3-point Internal Micrometers – Series 468 | MITUTOYO
DIGIMATIC HOLTEST – 3-POINT INTERNAL MICORMETER | MITUTOYO
Order No. : 468-173
Range : 87-100 mm
Description :
• Three-point internal micrometer with large LCD readout. (Character height 7.4 mm)
• Deep holes can be measured by attaching an Extension Rod (optional).
• Measurements can be made close to the bottom of a blind hole.
• Titanium-coated measuring pins provide excellent durability and impact resistance.
• Two preset values can be stored as reference points. -
468-973 | Digimatic Holtest – 3-point Internal Micrometers Set (Interchange-Head Set) – Series 468 | MITUTOYO
DIGIMATIC HOLTEST – 3-POINT INTERNAL MICORMETER SET | MITUTOYO
Interchange-Head Set
Order No. : 468-973
Range : 20-50 mm
Description :
• Three-point internal micrometer with large LCD readout. (Character height 7.4 mm)
• Deep holes can be measured by attaching an Extension Rod (optional).
• Measurements can be made close to the bottom of a blind hole.
• Titanium-coated measuring pins provide excellent durability and impact resistance.
• Two preset values can be stored as reference points. -
368-171 | Holtest – Three-Point Internal Micrometer Holtest 62-75mm | MITUTOYO
3-POINT INTERNAL MICROMETER HOLTEST | MITUTOYO
Order No. 368-171
Range. 62-75 mm
Description
• Titanium-coated measuring pins on the three-point type (over 6 mm range models) provide excellent durability and impact resistance.
• Three-point internal micrometer with measuring range 6 mm or longer allows stable measurement through self-centering.
• Measurement can be made close to the bottom of a blind hole.
• Deep holes can be measured by attaching an Extension Rod (optional) which is available on models over 6 mm (0.275 in) measuring range. -
368-778 | Holtest (Type II) – 3 Point Internal Micrometer 200-225mm | MITUTOYO
3-POINT INTERNAL MICROMETER HOLTEST (TYPE II) MITUTOYO
Order No. : 368-778
Range: 200-225mm
Description
• Holtests type II is equipped with contact points of alloy steel and has the same accuracy as the titanium model.
• Constant-force device allows stable measurement.
• Deep holes can be measured by attaching an Extension Rod (optional). -
568-471 | ABSOLUTE BOREMATIC SERIES 568 – ABSOLUTE DIGIMATIC SNAP-OPEN BORE GAGES 2-2.5″ | MITUTOYO
ABSOLUTE BOREMATIC SERIES 568
ABSOLUTE DIGIMATIC SNAP-OPEN BORE GAGES
Range : 2.5-3″
Order No. : 568-471
Description :
This is a individual unit Three-Point Digimatic Snap Open Bore Gauge.
It offers you the following benefits:- It enables you to take measurements easily and quickly.
- Titanium-coated measuring pins gives you excellent durability and impact resistance.
- 330° rotatable display unit also gives you easy reading at any angle.
- GO/NG tolerance judgement function.
-
133-153 | TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE, 300-325mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE
Order No. : 133-153
Range : 300-325mm
Description :
• Standard Single-Rod Type inside micrometer.
• Carbide measuring faces.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker and Gauge Block Accessory Sets are available as reference gages datum adjustment. -
337-301 | TUBULAR INSIDE MICROMETERS SERIES 337 – EXTENSION ROD TYPE, 200-1000 mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 337 – EXTENSION ROD TYPE
Order No. : 337-301
Range : 200-1000mm
Description :
• Wide range of inside measurements possible by combining Extension Rods and anvils with the micrometer head.
• Two types of measuring faces are available; with or without carbide tip. (The 337 Series is only available with carbide tip)
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• An inside length standard is required for accurately setting the micrometer. -
145-188 | INSIDE MICROMETER SERIES 145 – CALIPER TYPE, 75-100mm | MITUTOYO
INSIDE MICROMETER SERIES 145 – CALIPER TYPE
Order No. 145-188
Range: 75-100mm
Description:
• Carbide measuring faces.
• Equipped with a constant measuring-force device.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker (more than 25 mm) and Gauge Block Accessory Sets are available as reference gages for datum adjustment.
