- Sort by Popularity
- Display 12 Products per page
-
611659-021 | Individual Metric Rectangular Gauge Blocks – 19.5mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 19.5mm | Mitutoyo
Order No. : 611659-021
Length : 19.5 mm
Description :
This Grade 0 Gauge Block with Inspection Certificate offers you the following benefits:
- Outstanding dimensional stability: Mitutoyo steel gauge blocks are made exclusively from artificially aged material.
- High gauge reliability: The gauge blocks can be used as a standard for a long time due to their high dimensional stability.
- The maximum permitted length changes to gauge blocks over a year are defined in EN ISO 3650. Mitutoyo high-quality gauge blocks easily meet these and all other requirements.
- Steel gauge blocks are excellent for use as a standard because of the low measurement uncertainty that can be achieved when using them.
- Mitutoyo steel gauge blocks have top-quality surfaces, guaranteeing high wringing force.
-
611676 | Individual Metric Rectangular Gauge Blocks – 60mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 60mm | Mitutoyo
Order No. : 611676
Length : 60 mm
Description :
• If using only one length repeatedly, it is suggested to purchase individual gauge blocks.
• Nominal sizes which are not included in the chart below can be supplied custom-made on request.
• Each Grade K gauge block to ISO/DIN/JIS, BS or ASME standard is supplied with a Certificate of Calibration which certifies that the gauge block was calibrated by interferometry. -
2046A | Dial Indicator SERIES 2 — Standard Type, 0.01 mm Graduation | MITUTOYO
Dial Indicator SERIES 2 — Standard Type, 0.01 mm Graduation | MITUTOYO
• Standard 0.01 mm graduation dial gages having a bezel with an outside diameter of 57 mm.
• The bezel clamp and lifting lever (optional) can be attached to either the right or left side. These parts can be easily installed and removed without tools.
• Watertight assembly of bezel and crystal as well as the use of an O-ring prevents water or oil penetration.
• The stem and spindle are made of high-strength quench-hardened stainless steel suitable for heavy-duty use.
• A carbide contact point is used.
• The grand gear is made of stainless steel with high resistance to wear and deformation.
• Application of an anti-reflective and hard surface coating improves scale visibility along with scratch and chemical resistance. -
511-501 | BORE GAGE SERIES 511 – ABSOLUTE DIGIMATIC BORE GAGE, 45-100mm | MITUTOYO
BORE GAGE SERIES 511 – ABSOLUTE DIGIMATIC BORE GAGE, 45-100mm | MITUTOYO
Order No. : 511-501
Range: 45-100 mm
Description
• These ABSOLUTE Digimatic bore gages are exclusively designed for inside diameter measurement.
• ABS (ABSOLUTE) type bore gages are not subject to overspeed error.
• Up to four Extension Rods (optional) can be connected for measuring at the bottom of a hole 2 m deep.
• The display and grip can be rotated up to 320° and the display can be inclined up to 90°, so that it is easily readable from any direction.
• The minimum value holding function provides easy measurement of hole diameter. -
PC-4 | Level Type Dial Indicators Pic Test – 0.002mm | PEACOCK
Level Type Dial Indicators Pic Test PC-4 PEACOCK
● Miniature Bearing Used
The miniature bearing used as a bearing at the pivot of
the contact point to show good indication stability
without any effect by rod play.
● O-ring used
Oil resistance is enhanced by seating the O-ring in the
turning section of the outer frame. -
573-181-30 | ABSOLUTE SNAP CALIPER SERIES 573, 0-100mm | MITUTOYO
ABSOLUTE SNAP CALIPER SERIES 573
Order No. 573-181-30
Range : 0 – 100mm
Description :
• An ABSOLUTE electromagnetic induction linear encoder system is incorporated.
• Snap mechanism allows continuous and easy measurement without moving the
slider by using the lever.
• Displacement of snap part is 2 mm.
• Measuring force: 7 N to 14 N -
342-251-30 | Point Micrometer – Series 342, 0-25 mm | MITUTOYO
POINT MICROMETER – SERIES 342
Order No. : 342-251-30
Range : 0-25 mm
• Ideal tool for measuring drill web diameters, small grooves and other hard-to-reach points.
• The measuring points (carbide tipped) have approximately 0.3 mm radius.
• IP65 Digimatic micrometers.
• Equipped with Ratchet Stop for constant measuring force.