- Sort by Popularity
- Display 36 Products per page
-
133-146 | TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE, 125-150mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE
Order No. : 133-146
Range : 125-150mm
Description :
• Standard Single-Rod Type inside micrometer.
• Carbide measuring faces.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker and Gauge Block Accessory Sets are available as reference gages datum adjustment. -
133-178 | TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE, 925-950 mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE
Order No. : 133-178
Range : 925-950mm
Description :
• Standard Single-Rod Type inside micrometer.
• Carbide measuring faces.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker and Gauge Block Accessory Sets are available as reference gages datum adjustment. -
140-160 | TUBULAR INSIDE MICROMETER SERIES 140 – EXTENSION PIPE TYPE, 1000-5000mm | MITUTOYO
TUBULAR INSIDE MICROMETER SERIES 140 – EXTENSION PIPE TYPE
Order No.: 140-160
Range : 1000-5000mm
Description :
• Wide range of inside measurements possible by combining Extension Pipes and anvils with the micrometer head.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• An inside length standard is required for accurately setting the micrometer. -
526-150-10 | BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES, 3.70-7.30mm | MITUTOYO
BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES
บอร์เกจ – สำาหรับรูขนาดเล็กมาก
Order No.: 526-150-10
Range: 3.70-7.30 mm
Description:
• This series allows for agile and highly accurate comparative measurement of ø1 to 7 mm inside diameters.
• We offer an array of indicators. Contact us if you prefer any indicator other than the standard recommended indicator.
• Optional stand (215-120-10) is available for efficient measurement of multiple small holes. -
511-706 | BORE GAGE SERIES 511, 250-400mm | MITUTOYO
BORE GAGE SERIES 511
Order No.: 511-706
Range: 250-400 mm
Description:
• This series includes models for highly accurate measurement of ø18 to 400 mm inside diameters.
• The contact point and anvil have a carbide ball tip that is highly durable and abrasion-resistant.
• The grip minimizes the variation of indicator values by reducing heat transfer from the operator’s hand.
• Optional extension rods are available for measuring deep holes. Customized products with a longer rod below the grip are also available upon request. -
511-823-20 | BORE GAGE SERIES 511 – WITH MICROMETER HEAD, 60-100mm | MITUTOYO
BORE GAGE SERIES 511 – WITH MICROMETER HEAD
Order No.: 511-823-20
Range: 60-100 mm
Description:
• This series includes models for measuring ø60 to 800 mm inside diameters.
• The micrometer head is used for dimensional setting. The dimension can be easily changed without replacing the anvil and washer.
• The contact point has a carbide ball tip that is highly durable and abrasion-resistant.
• The grip minimizes the variation of indicator values affected by heat transfer from the operator’s hand. -
953558 | EXTENSION ROD SERIES 511 – ACCESSORIES FOR BORE GAGE | MITUTOYO
EXTENSION ROD SERIES 511 – ACCESSORIES FOR BORE GAGE | MITUTOYO
Order No. 953558
Description
• Extension Rods enable measurement of deeper holes when attached to a bore gage.
Note 1: When using an extension rod that is 500 mm or longer, hold the bore gage upright during measurement.
Note 2: Only one extension rod can be attached to a bore gage. It is not possible to use more than one extension rod.
Note 3: The extension rod cannot be used for products with a custom size or custom specifications.
-
177-286 | SETTING RINGS SERIES 177 – STEEL | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-286
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
177-432 | SETTING RINGS SERIES 177 – CERA | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-432
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
500-763-20 | ABSOLUTE COOLANT PROOF CALIPER SERIES 500 – with Dust/Water Protection Conforming to IP67 Level | MITUTOYO
ABSOLUTE COOLANT PROOF CALIPER SERIES 500 – with Dust/Water Protection Conforming to IP67 Level
Brand : Mitutoyo
Order No. : 500-763-20
Range : 0-8″
Description :
• Can be used in workshop conditions exposed to coolant, water, dust or oil.
100% air-leak test ensures every caliper conforms to IP67.
• Incorporates Mitutoyo’s ABSOLUTE measurement system. No need to reset the origin.
• Easy to use — advanced ergonomic design uses only 1 button.
• Battery cap does not require a screw driver for battery replacement.
• Can be integrated into statistical process control and measurement systems. -
500-167-30 | ABSOLUTE DIGIMATIC CALIPER with exclusive ABSOLUTE Encoder Technology | MITUTOYO
ABSOLUTE DIGIMATIC CALIPER with exclusive ABSOLUTE Encoder Technology
*Carbide-tipped jaws for outside measurement*
Order No. : 500-167-30
Range : 0-12″
Description :
• The ZERO/ABS button allows the display to be Zero-Set at any slider position along the scale. In addition, no overspeed-errors will occur.
• Carbide-tipped jaw calipers are optimal for rough finished parts, castings, grinding stones, etc.
• Allows integration into statistical process control and measurement systems for models with measurement data output connector. -
530-501 | VERNIER CALIPER SERIES 530 – STANDARD MODEL 0-600mm | MITUTOYO
VERNIER CALIPER SERIES 530 – STANDARD MODEL
Order No. 530-501
Range : 0 – 600 mm
Description :
• Stepped graduation face prevents dust ingress between the main scale and slider.
• The small vernier face angle (14°) provides easy reading.
• Can measure steps, since the end faces of the beam and slider are the zero reference point (measuring face). Standard calipers allow four types of measurement, i.e. outside, inside, depth, and step.
• Carbide-tipped jaw calipers are optimal for rough finished parts, castings, grinding stones, etc.
