- Sort by Popularity
- Display 12 Products per page
-
QLK | ADJUSTABLE, RATCHET TORQUE WRENCHSประแจปอนด์แบบปรับตั้งแรงขัน หัวฟรีซ้าย-ขวา BESTOOL-KANON
ประแจปอนด์แบบปรับตั้งแรงขัน หัวฟรีซ้าย-ขวา
QLK | ADJUSTABLE, RATCHET TORQUE WRENCHSFreely set torque values within the capacity range. Replaceable socket, ratchet wrenches.
FEATURES
● The ratchet improves efficiency. These wrenches are well suited forepetitive work.
● By replacing the sockets, various sizes of fasteners can be tightened within the tool’s capacity range.
● By reversing the ratchet, the wrench can be used to loosen fasteners counter-clockwise.
● Tightening to a torque setting can only be done clockwise.
● Accuracy : ±3% of indicated value over the full range.ADJUSTABLE THE TORQUE SETTING
♦ 30QLK~5600QLK
(1) Lossen the lock screw. (See Fig.1)
(2) Turn the sub-scale and adjust to a torque value
(the main scale plus the sub-scale) (See Fig.2)
(3) Tighten the lock screw.
(If the lock screw hits the pin before completely tightening, then change the position of the pin)
♦ 7000QLK~21000QLK-8
(1) When applicable, mount the extension bar snugly all the way onto the body of the wrench.
(2) With the extension bar mounted (See Fig.3), insert the hexagonal side of the adjusting box wrench.
● Without the extension bar (See Fig.4), insert the hexagonal side of the adjusting box wrench into the body.
(3) Turn the adjusting box wrench to set the torque value. (the main scale plus the sub-scale) -
107-202 | Indicator Type Micrometer Series 107, 25-50 mm | Mitutoyo
Indicator Type Micrometer Series 107 (without indicator)
Range : 25-50 mm
Order No. : 107-202
• Designed to mount a dial indicator for direct GO/±NG judgment on mass-produced parts.
• Anvil retracting trigger for quick measurement.
• Various kinds of indicators* are selectable depending on the measurement type
(accuracy required, measuring range, etc.).
• Measuring faces: Carbide.
• Anvil stroke: 3 mm.
* Indicators with stems cannot be installed on this micrometer. -
122-108-10 | Blade Micrometer – non rotating spindle type – Series 122 | MITUTOYO
Blade Micrometer – non rotating spindle type – Series 122
Range: 175-200 mm
Order No.: 122-108-10
• The anvil and spindle are blade-shaped for measuring the groove diameter of shafts, keyways, and other hard-to-reach features.
• Carbide-tipped measuring faces are available.
• Non-rotating spindle type.
• Equipped with Ratchet Stop for constant measuring force. -
105-412 | Outside Micrometer with Anvil Extension Collars 1400-1500 mm | MITUTOYO
Order No. 105-412
Outside Micrometer with Anvil Extension Collars
Range : 1400-1500 mm
MITUTOYO
• Large, lightweight micrometer with excellent strength based on a pipe structure frame made of a combination of square and round pipes.
• Wide measuring range with anvil extension collars.
• 50 mm/ 2 in spindle stroke.
• Measuring faces: Carbide.
• Equipped with Ratchet Stop for constant measuring force. -
126-128 | Screw Thread Micrometer Interchangeable Anvil/Spindle Tip Type 75-100 mm | MITUTOYO
Screw Thread Micrometer
Order No. 126-128
Range : 75-100 mm
• Use by installing a suitable interchangeable anvil / spindle tip pair.
• Direct reading of screw pitch diameter (no need for calculation).
• Series 326 is a protection grade IP65, waterproof Digimatic screw thread micrometer with interchangeable anvil / spindle tip.
• Equipped with Ratchet Stop for constant measuring force.
• Supplied with a setting standard for adjusting zero point for metric (unified) 60º threads.
• Interchangeable anvils / spindle tips are optional. -
324-252-30 | Gear Tooth Micrometer IP65, 25-50 mm | MITUTOYO
Gear Tooth Micrometer – Interchangeable Ball Anvil / Spindle Tip Type
Order No. : 324-252-30
Range : 25-50 mm
• Measures over-pin diameter of gears using precision steel (or carbide) ball anvils / spindle tips.
• IP65 Digimatic gear tooth micrometers.
• Interchangeable ball anvils/spindle tips for various gear modules (0.5 to 5.25) are optional.
• Ball anvil / spindle tips: optional.