- Sort by Popularity
- Display 12 Products per page
-
339-102 | TUBULAR INSIDE MICROMETER SERIES 339 – EXTENSION PIPE TYPE, 8-9″ | MITUTOYO
TUBULAR INSIDE MICROMETER SERIES 339 – EXTENSION PIPE TYPE
Order No.: 339-102
Range : 8-9″
Description :
• Wide range of inside measurements possible by combining Extension Pipes and anvils with the micrometer head.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• An inside length standard is required for accurately setting the micrometer.
• IP65 (water-proof) protection level that enables use in the presence of cutting fluid. -
128-101 DEPTH MICROMETER SERIES 128, 0-25mm, Base 63.5×16 | MITUTOYO
DEPTH MICROMETER SERIES 128 – MITUTOYO
Order No. : 128-101
Range : 0-25 mm
Base : 63.5×16
Description :
This Depth Micrometer offers you the following benefits:
- ø4mm measuring rod.
- Ratchet stop provides you with constant measuring force.
- Measuring rod lock.
- Carbide-tipped measuring rod model is available.
-
QLK | ADJUSTABLE, RATCHET TORQUE WRENCHSประแจปอนด์แบบปรับตั้งแรงขัน หัวฟรีซ้าย-ขวา BESTOOL-KANON
ประแจปอนด์แบบปรับตั้งแรงขัน หัวฟรีซ้าย-ขวา
QLK | ADJUSTABLE, RATCHET TORQUE WRENCHSFreely set torque values within the capacity range. Replaceable socket, ratchet wrenches.
FEATURES
● The ratchet improves efficiency. These wrenches are well suited forepetitive work.
● By replacing the sockets, various sizes of fasteners can be tightened within the tool’s capacity range.
● By reversing the ratchet, the wrench can be used to loosen fasteners counter-clockwise.
● Tightening to a torque setting can only be done clockwise.
● Accuracy : ±3% of indicated value over the full range.ADJUSTABLE THE TORQUE SETTING
♦ 30QLK~5600QLK
(1) Lossen the lock screw. (See Fig.1)
(2) Turn the sub-scale and adjust to a torque value
(the main scale plus the sub-scale) (See Fig.2)
(3) Tighten the lock screw.
(If the lock screw hits the pin before completely tightening, then change the position of the pin)
♦ 7000QLK~21000QLK-8
(1) When applicable, mount the extension bar snugly all the way onto the body of the wrench.
(2) With the extension bar mounted (See Fig.3), insert the hexagonal side of the adjusting box wrench.
● Without the extension bar (See Fig.4), insert the hexagonal side of the adjusting box wrench into the body.
(3) Turn the adjusting box wrench to set the torque value. (the main scale plus the sub-scale) -
107-202 | Indicator Type Micrometer Series 107, 25-50 mm | Mitutoyo
Indicator Type Micrometer Series 107 (without indicator)
Range : 25-50 mm
Order No. : 107-202
• Designed to mount a dial indicator for direct GO/±NG judgment on mass-produced parts.
• Anvil retracting trigger for quick measurement.
• Various kinds of indicators* are selectable depending on the measurement type
(accuracy required, measuring range, etc.).
• Measuring faces: Carbide.
• Anvil stroke: 3 mm.
* Indicators with stems cannot be installed on this micrometer. -
122-108-10 | Blade Micrometer – non rotating spindle type – Series 122 | MITUTOYO
Blade Micrometer – non rotating spindle type – Series 122
Range: 175-200 mm
Order No.: 122-108-10
• The anvil and spindle are blade-shaped for measuring the groove diameter of shafts, keyways, and other hard-to-reach features.
• Carbide-tipped measuring faces are available.
• Non-rotating spindle type.
• Equipped with Ratchet Stop for constant measuring force. -
105-412 | Outside Micrometer with Anvil Extension Collars 1400-1500 mm | MITUTOYO
Order No. 105-412
Outside Micrometer with Anvil Extension Collars
Range : 1400-1500 mm
MITUTOYO
• Large, lightweight micrometer with excellent strength based on a pipe structure frame made of a combination of square and round pipes.
• Wide measuring range with anvil extension collars.
• 50 mm/ 2 in spindle stroke.
• Measuring faces: Carbide.
• Equipped with Ratchet Stop for constant measuring force.