- Sort by Popularity
- Display 12 Products per page
-
611651-021 | Individual Metric Rectangular Gauge Blocks – 11.5mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 11.5mm | Mitutoyo
Order No. : 611651-021
Length : 11.5 mm
Description :
This Grade 0 Gauge Block with Inspection Certificate offers you the following benefits:
- Outstanding dimensional stability: Mitutoyo steel gauge blocks are made exclusively from artificially aged material.
- High gauge reliability: The gauge blocks can be used as a standard for a long time due to their high dimensional stability.
- The maximum permitted length changes to gauge blocks over a year are defined in EN ISO 3650. Mitutoyo high-quality gauge blocks easily meet these and all other requirements.
- Steel gauge blocks are excellent for use as a standard because of the low measurement uncertainty that can be achieved when using them.
- Mitutoyo steel gauge blocks have top-quality surfaces, guaranteeing high wringing force.
-
611673-021 | Individual Metric Rectangular Gauge Blocks – 30mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 30mm | Mitutoyo
Order No. : 611673-021
Length : 30 mm
Description :
This Grade 0 Gauge Block with Inspection Certificate offers you the following benefits:
- Outstanding dimensional stability: Mitutoyo steel gauge blocks are made exclusively from artificially aged material.
- High gauge reliability: The gauge blocks can be used as a standard for a long time due to their high dimensional stability.
- The maximum permitted length changes to gauge blocks over a year are defined in EN ISO 3650. Mitutoyo high-quality gauge blocks easily meet these and all other requirements.
- Steel gauge blocks are excellent for use as a standard because of the low measurement uncertainty that can be achieved when using them.
- Mitutoyo steel gauge blocks have top-quality surfaces, guaranteeing high wringing force.
-
611844 | Individual Metric Rectangular Gauge Blocks – 900mm | Mitutoyo
Individual Metric Rectangular Gauge Blocks – 900mm | Mitutoyo
Order No. : 611844
Length : 900 mm
Description :
• If using only one length repeatedly, it is suggested to purchase individual gauge blocks.
• Nominal sizes which are not included in the chart below can be supplied custom-made on request.
• Each Grade K gauge block to ISO/DIN/JIS, BS or ASME standard is supplied with a Certificate of Calibration which certifies that the gauge block was calibrated by interferometry. -
515-376 | DIGITAL HEIGHT MASTER Series 515 | MITUTOYO
• For calibrating and setting height gages.
• Staggered arrangement of block stack have two measuring faces on the same level, one facing up and the other down.
• Equipped with a data output port that enables incorporation into measurement networking and statistical process control systems.
-
K220T | Measurement of foamed material and foils – Measuring range : 0-20 mm | KROEPLIN
Measurement of foamed material and foils
Measuring range : 0-20 mm
Order No. : K220T
-
573-718-20 | ABSOLUTE BACK-JAW CENTERLINE CALIPER SERIES 573 -EDGE-TO-CENTER TYPE, 10.1-200mm | MITUTOYO
ABSOLUTE BACK-JAW CENTERLINE CALIPER SERIES 573
EDGE-TO-CENTER TYPE
Order No.: 573-718-20
Range: 10.1-200 mm
Description :
The ABSOLUTE Digimatic back-jaw centreline calipers offer you the following benefits:
- Specially designed to allow you to measure hole centre-to-centre or edge-to-centre distances.
- You can read measurements more easily from above, thanks to the jaws being on the back of the slide.
- Direct reading of pitch measurements is also available due to the offset value setting function.
-
126-130 | Screw Thread Micrometer Interchangeable Anvil/Spindle Tip Type 125-150 mm | MITUTOYO
Screw Thread Micrometer
Order No. 126-130
Range : 125-150 mm
• Use by installing a suitable interchangeable anvil / spindle tip pair.
• Direct reading of screw pitch diameter (no need for calculation).
• Series 326 is a protection grade IP65, waterproof Digimatic screw thread micrometer with interchangeable anvil / spindle tip.
• Equipped with Ratchet Stop for constant measuring force.
• Supplied with a setting standard for adjusting zero point for metric (unified) 60º threads.
• Interchangeable anvils / spindle tips are optional. -
167-102 | Setting Standards for Outside Micrometer – SERIES 167 | Mitutoyo
SETTING STANDARD FOR OUTSIDE MICROMETER – SERIES 167
Description
- Used for adjusting the reference point of outside micrometers
Order No. 167-102
Length : 50 mm
-
148-853 | Micrometer Heads – Small Thimble Dimeter Standard Type – SERIES 148 | MITUTOYO
MICROMETER HEAD – SMALL THIMBLE DIMETER STANDARD TYPE – SERIES 148
Order no. 148-853
Range: 0-13mm
Description :
• Measuring range of 13 mm.
• The thimble can be set to zero at any position by loosening the setscrew. -
151-255 | Micrometer Heads – Medium-size standard Type with 8mm Diameter Spindle – SERIES 151 | MITUTOYO
MICROMETER HEAD – MEDIUM-SIZED STANDARD TYPE
With 8mm Diameter Spindle – SERIES 151
MITUTOYO
Order no. 151-255
Range: 0-50mm
Description :
• Larger spindle (ø8 mm) for heavy-duty applications (normally ø6.35 mm).
