- Sort by Popularity
- Display 12 Products per page
-
568-936 | ABSOLUTE BOREMATIC SERIES 568 – NON-INTERCHANGEABLE-HEAD SNAP-OPEN BORE GAGE STES | MITUTOYO
ABSOLUTE BOREMATIC SERIES 568
INTERCHANGEABLE-HEAD BORE GAGE STES
Order No. : 568-936
Description :
• The Borematic allows quick and easy measurement with lever operation.
• Titanium-coated measuring pins provide excellent durability and impact resistance.
• Three-Point contact measuring head enables stable measurement.
• Deep holes can be measured by attaching an Extension Rod (optional). -
133-164 | TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE, 575-600mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE
Order No. : 133-164
Range : 575-600mm
Description :
• Standard Single-Rod Type inside micrometer.
• Carbide measuring faces.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker and Gauge Block Accessory Sets are available as reference gages datum adjustment. -
137-208 | TUBULAR INSIDE MICROMETERS SERIES 137 – EXTENSION ROD TYPE, 50-500mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 137 – EXTENSION ROD TYPE
Order No.: 137-208
Range : 50-500mm
Description :
• Wide range of inside measurements possible by combining Extension Rods and anvils with the micrometer head.
• Two types of measuring faces are available; with or without carbide tip. (The 337 Series is only available with carbide tip)
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• An inside length standard is required for accurately setting the micrometer. -
141-103 | INSIDE MICROMETERS SERIES 141 – INTERCHANGEABLE ROD TYPE CARBIDE TIPPED , 25-50mm | MITUTOYO
INSIDE MICROMETERS SERIES 141 – INTERCHANGEABLE ROD TYPE – CARBIDE TIPPED
Order No. 141-103
Range: 25-50mm
Description:
• Wide range of inside measurements possible by combining one or more Interchangeable Rods.
• For models supplied with more than one Interchangeable Rod, the full measuring range is achieved by combining spacing collars with the rods. -
526-124-20 | BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES, 7-10mm | MITUTOYO
BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES
Order No.: 526-124-20
Range: 7-10 mm
Description:
• This series allows for agile and highly accurate comparative measurement of ø7 to 18 mm inside diameters.
• We offer an array of indicators. Contact us if you prefer any indicator other than the standard recommended indicator.
• Optional stand (215-120-10) is available for efficient measurement of multiple small holes. -
511-762 | BORE GAGE SERIES 511 – SHORT LEG TYPE, 35-60mm | MITUTOYO
BORE GAGE SERIES 511 – SHORT LEG TYPE
Order No.: 511-762
Range: 35-60 mm
Description:
• As it is light and easy to handle with a short rod below the grip, the operator can work smoothly when inserting it into a narrow space or measuring an object on the table.
• The contact point and anvil have a carbide ball tip that is highly durable and abrasion resistant.
• The grip minimizes the variation of indicator values affected by heat transfer from the operator’s hand. -
511-436-20 | BORE GAGES SERRIES 511 – for BLIND HOLES, 35-60mm | MITUTOYO
BORE GAGE SERIES 511 FOR BLIND HOLES
Order No.: 511-436-20
Range: 35-60mm
Description :
• Capable of ID (inside diameter) measurement close to the bottom of a hole.
• The contact point and anvil have a carbide ball tip that is highly durable and abrasion resistant.
• Optional Extension Rods can be attached for measuring deep holes. -
177-257 | SETTING RINGS SERIES 177 – STEEL | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-257
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
177-304 | SETTING RINGS SERIES 177 – STEEL | MITUTOYO
SETTING RING
Accessories for Inside Micrometers, Hotest and Dial Bore Gages
Brand : MITUTOYO
Order No. 177-304
Description :
• Used for quick and accurate setting of dial bore gages, Holtest, and inside micrometers.
• Actual diameter is marked in 0.001 mm increments. (Dimension measuring position is the center of the height T.) -
500-732-20 | ABSOLUTE COOLANT PROOF CALIPER SERIES 500 – with Dust/Water Protection Conforming to IP67 Level | MITUTOYO
ABSOLUTE COOLANT PROOF CALIPER SERIES 500 – with Dust/Water Protection Conforming to IP67 Level
Brand : Mitutoyo
Order No. : 500-732-20
Range : 0-8″
Description :
• Can be used in workshop conditions exposed to coolant, water, dust or oil.
100% air-leak test ensures every caliper conforms to IP67.
• Incorporates Mitutoyo’s ABSOLUTE measurement system. No need to reset the origin.
• Easy to use — advanced ergonomic design uses only 1 button.
• Battery cap does not require a screw driver for battery replacement.
• Can be integrated into statistical process control and measurement systems. -
500-172-30 | ABSOLUTE DIGIMATIC CALIPER SERIES 500 – with exclusive ABSOLUTE Encoder Technology | MITUTOYO
ABSOLUTE DIGIMATIC CALIPER SERIES 500 – with exclusive ABSOLUTE Encoder Technology
Order No. : 500-172-30
Range : 0-8″
Description :
• The ZERO/ABS button allows the display to be Zero-Set at any slider position along the scale. In addition, no overspeed-errors will occur.
• Carbide-tipped jaw calipers are optimal for rough finished parts, castings, grinding stones, etc.
• Allows integration into statistical process control and measurement systems for models with measurement data output connector. -
530-335 | VERNIER CALIPER SERIES 530 – STANDARD MODEL 0-150mm| MITUTOYO
VERNIER CALIPER SERIES 530 – STANDARD MODEL
*Carbide-Tipped jaws for outside and inside measurement*
Order No. 530-335
Range : 0 – 150 mm
Description :
• Stepped graduation face prevents dust ingress between the main scale and slider.
• The small vernier face angle (14°) provides easy reading.
• Can measure steps, since the end faces of the beam and slider are the zero reference point (measuring face). Standard calipers allow four types of measurement, i.e. outside, inside, depth, and step.
• Carbide-tipped jaw calipers are optimal for rough finished parts, castings, grinding stones, etc.