- Sort by Popularity
- Display 12 Products per page
-
7850 | Micro Jack SERIES 7 | MITUTOYO
MICRO JACK – SERIES 7
MITUTOYO
ORDER NO. : 7850
DESCRIPTION :
• Used for accurate leveling of machines, surface plates, and other precision instruments.
• Zero-setting is possible at any position.
• Easy adjustment under heavy load. -
468-174 | Digimatic Holtest – 3-point Internal Micrometers – Series 468 | MITUTOYO
DIGIMATIC HOLTEST – 3-POINT INTERNAL MICORMETER | MITUTOYO
Order No. : 468-174
Range : 100-125 mm
Description :
• Three-point internal micrometer with large LCD readout. (Character height 7.4 mm)
• Deep holes can be measured by attaching an Extension Rod (optional).
• Measurements can be made close to the bottom of a blind hole.
• Titanium-coated measuring pins provide excellent durability and impact resistance.
• Two preset values can be stored as reference points. -
468-974 | Digimatic Holtest – 3-point Internal Micrometers Set (Interchange-Head Set) – Series 468 | MITUTOYO
DIGIMATIC HOLTEST – 3-POINT INTERNAL MICORMETER SET | MITUTOYO
Interchange-Head Set
Order No. : 468-974
Range : 50-100 mm
Description :
• Three-point internal micrometer with large LCD readout. (Character height 7.4 mm)
• Deep holes can be measured by attaching an Extension Rod (optional).
• Measurements can be made close to the bottom of a blind hole.
• Titanium-coated measuring pins provide excellent durability and impact resistance.
• Two preset values can be stored as reference points. -
368-172 | Holtest – Three-Point Internal Micrometer Holtest 75-88mm | MITUTOYO
3-POINT INTERNAL MICROMETER HOLTEST | MITUTOYO
Order No. 368-172
Range. 75-88 mm
Description
• Titanium-coated measuring pins on the three-point type (over 6 mm range models) provide excellent durability and impact resistance.
• Three-point internal micrometer with measuring range 6 mm or longer allows stable measurement through self-centering.
• Measurement can be made close to the bottom of a blind hole.
• Deep holes can be measured by attaching an Extension Rod (optional) which is available on models over 6 mm (0.275 in) measuring range. -
368-780 | Holtest (Type II) – 3 Point Internal Micrometer 250-275mm | MITUTOYO
3-POINT INTERNAL MICROMETER HOLTEST (TYPE II) MITUTOYO
Order No. : 368-780
Range: 250-275mm
Description
• Holtests type II is equipped with contact points of alloy steel and has the same accuracy as the titanium model.
• Constant-force device allows stable measurement.
• Deep holes can be measured by attaching an Extension Rod (optional). -
568-473 | ABSOLUTE BOREMATIC SERIES 568 – ABSOLUTE DIGIMATIC SNAP-OPEN BORE GAGES 3.5-4″ | MITUTOYO
ABSOLUTE BOREMATIC SERIES 568
ABSOLUTE DIGIMATIC SNAP-OPEN BORE GAGES
Range : 3.5-4″
Order No. : 568-473
Description :
This is a individual unit Three-Point Digimatic Snap Open Bore Gauge.
It offers you the following benefits:- It enables you to take measurements easily and quickly.
- Titanium-coated measuring pins gives you excellent durability and impact resistance.
- 330° rotatable display unit also gives you easy reading at any angle.
- GO/NG tolerance judgement function.
-
133-155 | TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE, 350-375mm | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 133 – SINGLE ROD TYPE
Order No. : 133-155
Range : 350-375mm
Description :
• Standard Single-Rod Type inside micrometer.
• Carbide measuring faces.
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker and Gauge Block Accessory Sets are available as reference gages datum adjustment. -
337-303 | TUBULAR INSIDE MICROMETERS SERIES 337 – EXTENSION ROD TYPE, 8-40″ | MITUTOYO
TUBULAR INSIDE MICROMETERS SERIES 337 – EXTENSION ROD TYPE
Order No. : 337-303
Range : 8-40″
Description :
• Wide range of inside measurements possible by combining Extension Rods and anvils with the micrometer head.
• Two types of measuring faces are available; with or without carbide tip. (The 337 Series is only available with carbide tip)
• The sleeve is rotated to adjust the reference point adjustment when setting to a length standard.
• An inside length standard is required for accurately setting the micrometer. -
145-190 | INSIDE MICROMETER SERIES 145 – CALIPER TYPE, 125-150mm | MITUTOYO
INSIDE MICROMETER SERIES 145 – CALIPER TYPE
Order No. 145-190
Range: 125-150mm
Description:
• Carbide measuring faces.
• Equipped with a constant measuring-force device.
• Optional Setting Rings (nominal size below 300 mm), CERA Inside Micro Checker (more than 25 mm) and Gauge Block Accessory Sets are available as reference gages for datum adjustment. -
526-150-11 | BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES, 3.70 – 7.30mm | MITUTOYO
BORE GAGES SERIES 526 – FOR EXTRA SMALL HOLES
บอร์เกจ – สำาหรับรูขนาดเล็กมาก
Order No.: 526-150-11
Range: 3.70 – 7.30 mm
Description:
• This series allows for agile and highly accurate comparative measurement of ø1 to 7 mm inside diameters.
• We offer an array of indicators. Contact us if you prefer any indicator other than the standard recommended indicator.
• Optional stand (215-120-10) is available for efficient measurement of multiple small holes. -
511-724-20 | BORE GAGE SERIES 511, 100-160mm | MITUTOYO
BORE GAGE SERIES 511
Order No.: 511-724-20
Range: 100-160 mm
Description:
• This series includes models for highly accurate measurement of ø18 to 400 mm inside diameters.
• The contact point and anvil have a carbide ball tip that is highly durable and abrasion-resistant.
• The grip minimizes the variation of indicator values by reducing heat transfer from the operator’s hand.
• Optional extension rods are available for measuring deep holes. Customized products with a longer rod below the grip are also available upon request. -
511-816-20 | BORE GAGE SERIES 511 – WITH MICROMETER HEAD, 250-400mm | MITUTOYO
BORE GAGE SERIES 511 – WITH MICROMETER HEAD
Order No.: 511-816-20
Range: 250-400 mm
Description:
• This series includes models for measuring ø60 to 800 mm inside diameters.
• The micrometer head is used for dimensional setting. The dimension can be easily changed without replacing the anvil and washer.
• The contact point has a carbide ball tip that is highly durable and abrasion-resistant.
• The grip minimizes the variation of indicator values affected by heat transfer from the operator’s hand.
